DC7V-35V to DC1.25V-30V LED Driver Charging Constant Current Voltage Step Down Buck Power Supply Module
38
Ua palekana ka uku

ʻAe ʻia nā mea hoʻihoʻi i loko o 40 lā mai ka lā loaʻa. ʻAʻole hiki ke hoʻihoʻi i nā mea i hoʻohui ʻia. ʻAʻole hiki ke hoʻihoʻi i nā mea i kūʻai ʻia me ka kāleka makana.
Makana Manuahi
Aloha mai i Roymall, kāu pūnaewele kūʻai makana maikaʻi. Mahalo nui mākou i kāu kākoʻo, a hāʻawi mākou i makana manuahi me kēlā me kēia kūʻai. Mākaukau e ʻimi i kā mākou hōʻiliʻili? E nānā i kā mākou koho, kau i kāu kauoha, a e kali no kāu makana manuahi me kāu kūʻai.Kuleana Hoʻouna
Hoʻoponopono mākou i nā kauoha i loko o 2 lā.ʻO ka manawa hoʻouna maʻamau he 5-7 lā hana.Hiki ke ʻokoʻa ka manawa hoʻouna ma muli o ke kahua.1. Kuleana Hoʻihoʻi
ʻAe mākou i nā mea i kūʻai ʻia mai roymall.com wale nō. ʻAʻole hiki ke hoʻihoʻi i nā makana manuahi. Pono e hoʻohana ʻole ʻia ka mea a i ʻole i loko o ka pūʻolo kumu.Hoʻoponopono mākou i nā hoʻihoʻi i loko o 3-5 lā hana ma hope o ka loaʻa.ʻAʻole hiki ke hoʻihoʻi i nā mea i hoʻohui ʻia.E kelepona iā mākou: service@roymall.com a i ʻole Whatsapp: +86193598494712.Kuleana Uku
E loaʻa iā ʻoe ka uku piha ma hope o ka loaʻa a me ka nānā ʻana. ʻAʻole hiki ke hoʻihoʻi i nā uku hoʻouna.E kelepona iā mākou: service@roymall.com a i ʻole Whatsapp: +8619359849471
Feature:
n
nThis module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable.
nThis module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV!
nThis module uses machine placement, reflow soldering.
nThis module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V.
nModule indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module.
n
nDescription:
n
nNature of the module: Non-isolated step-down module
nRectification: Non-synchronous rectification
nInput voltage: 7V - 35V
nOutput voltage: 1.25V - 30V
nOutput current: Adjustable, 3A (maximum)
nTransfer efficiency: 92% (maximum)
nSwitching frequency: 150KHz
noutput ripple: 50mV (maximum) 20M Kbps
nLoad regulation: ±0.5%
nVoltage regulation: ±2.5%
nOperating temperature: -40°C to +85°C
nDimension: 48 x 23 x 14mm (L x W x H)
n
nBattery charging method:
n
n1. Make sure the battery float voltage and charging current, the module input voltage;
n2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value;
n4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment)
n5. Adjustment constant potentiometer allows the output voltage reaches the float voltage;
n6. Connected to the battery and try to charge.
n(1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.)
n
nLED constant current driver using method:
n
n1. Make sure that the drive LED operating current and maximum working voltage;
n2. Adjustment constant potentiometer, output voltage adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current;
n4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED;
n5. Connect LED, test machine.
n(1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.)
n
nPackage included:
n
n1 x Buck module
n
n
n
nThis module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable.
nThis module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV!
nThis module uses machine placement, reflow soldering.
nThis module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V.
nModule indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module.
n
nDescription:
n
nNature of the module: Non-isolated step-down module
nRectification: Non-synchronous rectification
nInput voltage: 7V - 35V
nOutput voltage: 1.25V - 30V
nOutput current: Adjustable, 3A (maximum)
nTransfer efficiency: 92% (maximum)
nSwitching frequency: 150KHz
noutput ripple: 50mV (maximum) 20M Kbps
nLoad regulation: ±0.5%
nVoltage regulation: ±2.5%
nOperating temperature: -40°C to +85°C
nDimension: 48 x 23 x 14mm (L x W x H)
n
nBattery charging method:
n
n1. Make sure the battery float voltage and charging current, the module input voltage;
n2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value;
n4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment)
n5. Adjustment constant potentiometer allows the output voltage reaches the float voltage;
n6. Connected to the battery and try to charge.
n(1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.)
n
nLED constant current driver using method:
n
n1. Make sure that the drive LED operating current and maximum working voltage;
n2. Adjustment constant potentiometer, output voltage adjusted to about 5V.
n3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current;
n4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED;
n5. Connect LED, test machine.
n(1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.)
n
nPackage included:
n
n1 x Buck module
n
n

n
n

n
n

n
n

n
n

n
n

n
n
